Capacitive Touch Display
This display is directly compatible with the complete Colibri SoM family, as well as the Apalis T30 and the Apalis iMX6 Modules. It works with the Ixora and Aster Carrier Boards out-of-the-box.
7.0” WVGA 800 x 3 (RGB) x 480 High Brightness Capacitive Touch TFT Module for the use with Toradex Apalis and Colibri modules.
- 7" WVGA, a-Si TFT Display
- 18-bit RGB + TCON
- 40 pin and 10 pin FFC cable to connect it with a Carrier Board
- Atmel touch driver
Out-of-the-Box Experience with Toradex Carrier Boards
This display is directly compatible with the complete Colibri SoM family, as well as the Apalis T30, Apalis iMX6 and Apalis iMX8X. It works with the following Toradex Carrier Boards out-of-the-box:
- Ixora Carrier Board (from V1.1A)
- Aster Carrier Board
Using the Capacitive Touch Adapter, the following Boards are compatible as well:
Scope of delivery
- 7” Capacitive Touch Display Panel
- 10 Pins 0.5mm FFC Ribbon Cable
- 40 Pins 0.5mm FFC Ribbon Cable
The carrier board provides the necessary signal and power levels to the CoM. It also houses the application-specific connectivity and multimedia interfaces, such as USB, Ethernet, UART and HDMI.Learn more about SBCs and Carrier Boards
-20° to +85° C(1)
(1) This temperature range applies excluding the Ethernet connector
Toradex offers off-the-shelf accessories that can be directly used in end products. For a few of these accessories, design files including assembly drawings, schematics and Altium projects are available.
Toradex tests the peripherals listed in its webshop and works directly with vendors of Cameras, Modems, Displays, Sensors, and more, to make the integration with Toradex SoMs as easy as possible.
Capacitive Touch Displays for Apalis & Colibri modules
40 pin and 10 pin FFC cable (250mm) to connect it with a Carrier Board. Atmel touch driver. -20° to +70° C Temp, Range. Size: 173 x 112 x 13 mm.
Small form-factor Apalis Arm Computer Module family Carrier Board
Connectivity: USB 3.0: 2x Host, USB 2.0: 1x Host/ 1x OTG, Gigabit Ethernet, 2x I2C, 1x SPI, 4x PWM, 4x ADC, 2x CAN, 2x LEDs, up to 40 GPIOs
Multimedia: Audio out: 1x (Stereo), Audio in: 1x (Stereo), 1x/ 1x S/PDIF In/ Out, 1x 10 Bit Camera Parallel Interface, 4/5-wire Resistive Touch
Physical: 7-27V DC Supply Voltage, 5V 6A, 3.3V 8A On-Board Power Supplies, Size: 125 x 90 mm
Small form-factor with header compatible with Arduino Uno and Raspberry Pi (RPi) maker boards
Connectivity: USB 2.0: 2x Host, 1x Client (Shared), 10/100 Mbit Ethernet, 1x I2C, 1x SPI, 4x PWM, 4x ADC, 1x (Available with Colibri VFxx and iMX) CAN, up to 3x LEDs, up to 39 GPIOs
Multimedia: Audio out: 1x (Stereo), Audio in: 1x (Stereo), 1x Camera Parallel Interface, 4-wire Resistive Touch
Physical: 5V DC +/- 5% Supply Voltage, 3.3V 3A On-Board Power Supplies, Size: 100 x 80 mm
Capacitive Touch Adapter for the new Parallel Capacitive Touch Displays. .
-30° to +85° C Temp, Range. Size: 20 x 20 x 8.4 mm.